 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Philips Semiconductors 74LVC1G384 Bilateral switch 74LVC1G384 Bilateral switch Rev. 01 -- 26 February 2004 Product data sheet 1. General description The 74LVC1G384 is a high-speed Si-gate CMOS device. The 74LVC1G384 provides an analog switch. The switch has input and output terminals (pins Y and Z) and an active LOW enable input (pin E). When pin E is HIGH, the analog switch is turned off. 2. Features s Very low ON-resistance: x 7.5 (typ) at VCC = 2.7 V x 6.5 (typ) at VCC = 3.3 V x 6.0 (typ) at VCC = 5 V. s ESD protection: x HBM EIA/JESD22-A114-A exceeds 2 000 V x MM EIA/JESD22-A115-A exceeds 200 V. s High noise immunity s CMOS low power consumption s Direct interface TTL-levels s Latch-up performance meets requirements of JESD78 Class I s Multiple package options s Specified from -40 C to +80 C and -40 C to +125 C. 3. Quick reference data Table 1: Quick reference data Ground = 0 V; Tamb = 25 C; tr = tf 3.0 ns. Symbol tPZH, tPZL Parameter turn-on time E to Y or Z Conditions CL = 50 pF; RL = 500 VCC = 3.3 V VCC = 5.0 V tPHZ, tPLZ turn-off time E to Y or Z CL = 50 pF; RL = 500 VCC = 3.3 V VCC = 5.0 V CI input capacitance 5.4 3.6 2 ns ns pF 4.8 3.3 ns ns Min Typ Max Unit 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 1 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch Table 1: Quick reference data ...continued Ground = 0 V; Tamb = 25 C; tr = tf 3.0 ns. Symbol CPD CS Parameter power dissipation capacitance switch capacitance Conditions CL = 50 pF; fi = 10 MHz; VCC = 3.3 V OFF-state ON-state [1] CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD x VCC2 x fi + (CL + CS)x VCC2 x fo where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; CS = maximum switch capacitance in pF; VCC = supply voltage in V. The condition is VI = GND to VCC. [1] [2] Min - Typ 15.2 5 9.5 Max - Unit pF pF pF [2] 4. Ordering information Table 2: Ordering information Package Temperature range Name 74LVC1G384GW -40 C to +125 C 74LVC1G384GV -40 C to +125 C Description plastic surface mounted package; 5 leads plastic surface mounted package; 5 leads Version SOT353 SOT753 Type number 5. Marking Table 3: Marking Marking code YL YL Type number 74LVC1G384GW 74LVC1G384GV 6. Functional diagram Y Z 1 4# 1 1 X1 001aaa373 2 E 001aaa374 Fig 1. Logic symbol. Fig 2. IEC logic symbol. 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 2 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch Z Y E VCC 001aaa372 Fig 3. Logic diagram. 7. Pinning information 7.1 Pinning Y1 Z2 GND 3 001aaa365 5 VCC 384 4 E Fig 4. Pin configuration. 7.2 Pin description Table 4: Pin 1 2 3 4 5 Pin description Symbol Y Z GND E VCC Description independent input or output independent output or input ground (0 V) enable input (active LOW) supply voltage 8. Functional description 8.1 Function table Table 5: Input E L H [1] H = HIGH voltage level; L = LOW voltage level. Function table [1] Switch ON-state OFF-state 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 3 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch 9. Limiting values Table 6: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol VCC VI IIK ISK VS IS ICC, IGND Tstg Ptot [1] Parameter supply voltage input voltage input diode current switch diode current DC switch voltage range DC switch source or sink current VCC or GND current storage temperature power dissipation Conditions [1] Min -0.5 -0.5 -0.5 -65 Max +6.5 +6.5 -50 50 Unit V V mA mA VI < -0.5 V or VI > VCC + 0.5 V VI < -0.5 V or VI > VCC + 0.5 V enable and disable mode VS > -0.5 V or VS < VCC + 0.5 V VCC + 0.5 V 50 100 +150 250 mA mA C mW Tamb = -40 C to +125 C - The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 10. Recommended operating conditions Table 7: Symbol VCC VI VS Tamb tr, tf Recommended operating conditions Parameter supply voltage input voltage DC switch voltage range ambient temperature input rise and fall times VCC = 1.65 V to 2.7 V VCC = 2.7 V to 5.5 V [1] [1] Conditions Min 1.65 0 0 -40 0 0 Typ - Max 5.5 5.5 VCC +125 20 10 Unit V V V C ns/V ns/V To avoid drawing VCC current out of terminal Z, when switch current flows in terminal Y, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal Z, no VCC current will flow out of terminal Y. In this case there is no limit for the voltage drop across the switch. 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 4 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch 11. Static characteristics Table 8: Static characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol VIH Parameter C [1] VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V VIL LOW-level input voltage VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V ILI IS(OFF) IS(ON) ICC ICC input leakage current on control pin analog switch OFF-state current analog switch ON-state current quiescent supply current additional quiescent supply current per control pin input capacitance switch ON-state resistance (peak) VI = GND to VCC; see Figure 7 and Figure 8 IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V RON(rail) switch ON-state resistance rail VI = GND IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V VI = VCC IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V 9397 750 12675 Conditions Min 0.65 x VCC 1.7 2.0 0.7 x VCC [2] Typ 0.1 0.1 0.1 0.1 5 Max 0.35 x VCC 0.7 0.8 0.3 x VCC 5 5 5 10 500 Unit V V V V V V V V A A A A A Tamb = -40 C to +85 HIGH-level input voltage VI = 5.5 V or GND; VCC = 5.5 V VI = VIH or VIL; |VS| = VCC - GND; VCC = 5.5 V; see Figure 5 VI = VIH or VIL; |VS| = VCC - GND; VCC = 5.5 V; see Figure 6 VI = VCC or GND; VS = GND or VCC; IO = 0 A; VCC = 5.5 V VI = VCC - 0.6 V; VS = GND or VCC; IO = 0 A; VCC = 5.5 V - [2] [2] [2] [2] CI RON(peak) - 2 - pF - 35 14 11.5 8.5 6.5 10 8.5 7.5 6.5 6 12 8.5 7.5 6.5 6 130 30 25 20 15 30 20 18 15 10 30 20 18 15 10 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 5 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch Table 8: Static characteristics ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol RON(flat) Parameter switch ON-state resistance flatness Conditions VI = GND to VCC; see Figure 9 IS = 4 mA; VCC = 1.8 V IS = 8 mA; VCC = 2.5 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.3 V IS = 32 mA; VCC = 5.0 V Tamb = -40 C to +125 C VIH HIGH-level input voltage VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V VIL LOW-level input voltage VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V ILI IS(OFF) IS(ON) ICC ICC input leakage current on control pin analog switch OFF-state current analog switch ON-state current quiescent supply current additional quiescent supply current per control pin switch ON-state resistance (peak) VI = 5.5 V or GND; VCC = 5.5 V VI = VIH or VIL; |VS| = VCC - GND; VCC = 5.5 V; see Figure 5 VI = VIH or VIL; |VS| = VCC - GND; VCC = 5.5 V; see Figure 6 VI = VCC or GND; VS = GND or VCC; IO = 0 A; VCC = 5.5 V VI = VCC - 0.6 V; VS = GND or VCC; IO = 0 A; VCC = 5.5 V VI = GND to VCC; see Figure 7 IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V 180 45 38 30 23 0.65 x VCC 1.7 2.0 0.7 x VCC 0.35 x VCC 0.7 0.8 0.3 x VCC 100 200 200 200 5000 V V V V V V V V A A A A A [3] Min - Typ 100 17 10 5 3 Max - Unit RON(peak) 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 6 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch Table 8: Static characteristics ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol RON(rail) Parameter switch ON-state resistance rail Conditions VI = GND IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V VI = VCC IS = 4 mA; VCC = 1.65 V to 1.95 V IS = 8 mA; VCC = 2.3 V to 2.7 V IS = 12 mA; VCC = 2.7 V IS = 24 mA; VCC = 3.0 V to 3.6 V IS = 32 mA; VCC = 4.5 V to 5.5 V [1] [2] [3] Typical values are measured at Tamb = 25 C. These typical values are measured at VCC = 3.3 V These typical values are measured over the operating temperature range from -40 C to +125 C. Min - Typ - Max 45 30 27 23 15 45 30 27 23 15 Unit 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 7 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch VCC VIH IS E Y Z VIL IS VO GND 001aaa370 VCC E Y Z IS VI VI GND VO 001aaa369 VI = VCC and VO = GND; VI = GND and VO = VCC VI = VCC and VO = open circuit; VI = GND and VO = open circuit Fig 5. Test circuit for measuring switch OFF-state current. Fig 6. Test circuit for measuring switch ON-state current. 102 RON () mna673 VS VCC VIL E VCC = 1.8 V 2.5 V 10 Y Z IS 3.3 V 5.0 V GND 001aaa371 2.7 V VI 1 0 1 2 3 4 VI (V) 5 VI = GND to VCC; RON = VS/IS VS = GND to VCC. Fig 7. Test circuit for measuring switch ON-resistance. Fig 8. Typical switch ON-resistance as a function of input voltage. 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 8 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch 15 RON () 10 mna663 15 RON () 10 mna664 Tamb = +85 C +25 C -40 C Tamb = +85 C +25 C -40 C 5 5 0 0 0 1 2 Vl (V) 3 0 1 2 Vl (V) 3 a. VCC = 2.5 V 10 RON () 8 Tamb = +85 C mna665 b. VCC = 2.7 V 8 RON () 7 mna666 6 6 +25 C -40 C 4 4 2 5 Tamb = +85 C +25 C -40 C 3 0 0 1 2 3 Vl (V) 4 2 0 1 2 3 4 VI (V) 5 c. VCC = 3.3 V d. VCC = 5.0 V Fig 9. Switch ON-resistance at various supply voltages as a function of input voltage. 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 9 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch 12. Dynamic characteristics Table 9: Dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); test circuit Figure 12. Symbol tPHL, tPLH Parameter C [1] see Figure 10 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V tPZH, tPZL turn-on time E to Y or Z see Figure 11 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V tPHZ, tPLZ turn-off time E to Y or Z see Figure 11 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V CPD power dissipation capacitance CL = 50 pF; fi = 10 MHz; VI = GND to VCC VCC = 2.5 V VCC = 3.3 V VCC = 5.0 V Tamb = -40 C to +125 C tPHL, tPLH propagation delay Y to Z or Z to Y see Figure 10 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V tPZH, tPZL turn-on time E to Y or Z see Figure 11 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V 1.0 1.0 1.0 1.0 1.0 15.5 8.5 8.0 6.5 5.5 ns ns ns ns ns [2] [3] [4] [2] Conditions Min Typ Max Unit Tamb = -40 C to +85 propagation delay Y to Z or Z to Y 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 0.8 0.4 0.4 0.3 0.2 10.0 5.7 5.4 4.8 3.3 7.4 4.1 4.9 5.4 3.6 2.0 1.2 1.0 0.8 0.6 12.0 6.5 6.0 5.0 4.2 10.0 6.9 7.5 6.5 5.0 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns - 13.7 15.2 18.3 - pF pF pF - - 3.0 2.0 1.5 1.5 1.0 ns ns ns ns ns 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 10 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch Table 9: Dynamic characteristics ...continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V); test circuit Figure 12. Symbol tPHZ, tPLZ Parameter turn-off time E to Y or Z Conditions see Figure 11 VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V VCC = 3.0 V to 3.6 V VCC = 4.5 V to 5.5 V [1] [2] [3] All typical values are measured at Tamb = 25 C. tPHL and tPLH propagation delay is the calculated RC time constant of the typical switch ON-resistance of the switch and the specified capacitance when driven by an ideal voltage source (zero output impedance). CPD is used to determine the dynamic power dissipation (PD in W). PD = CPD x VCC2 x fi + (CL + CS)x VCC2 x fo where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; CS = maximum switch capacitance in pF; VCC = supply voltage in V. The condition is VI = GND to VCC. Min 1.0 1.0 1.0 1.0 1.0 Typ - Max 13.0 9.0 9.5 8.5 6.5 Unit ns ns ns ns ns [4] 13. Waveforms VI Y or Z input GND t PHL VOH Z or Y output VOL mna667 VM t PLH VM Measurement points are given in Table 10. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 10. Input (Y or Z) to output (Z or Y) propagation delays. Table 10: VCC 1.65 V to 1.95 V 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V Measurement points Input VM 0.5 x VCC 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC Output VM 0.5 x VCC 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC Supply voltage 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 11 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch VI E GND tPLZ VCC Y or Z output LOW-to-OFF OFF-to-LOW VOL tPHZ VOH Y or Z output HIGH-to-OFF OFF-to-HIGH GND switch enabled switch disabled switch enabled 001aaa375 VM tPZL VM VX tPZH VY VM Measurement points are given in Table 11. Logic levels: VOL and VOH are typical output voltage drop that occur with the output load. Fig 11. Turn-on and turn-off times. Table 11: VCC 1.65 V to 1.95 V 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V Measurement points Input VM 0.5 x VCC 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC Output VM 0.5 x VCC 0.5 x VCC 1.5 V 1.5 V 0.5 x VCC VX VOL + 0.1 x VCC VOL + 0.1 x VCC VOL + 0.3 V VOL + 0.3 V VOL + 0.3 V VY VOH - 0.1 x VCC VOH - 0.1 x VCC VOH - 0.3 V VOH - 0.3 V VOH - 0.3 V Supply voltage 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 12 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch VEXT VCC PULSE GENERATOR VI D.U.T. RT CL RL VO RL mna616 Test data is given in Table 12. Definitions test circuit: RT = Termination resistance should be equal to output impedance Zo of the pulse generator. CL = Load capacitance including jig and probe capacitance. RL = Load resistance. VEXT = Test voltage for switching times. Fig 12. Load circuitry for switching times. Table 12: VCC 1.65 V to 1.95 V 2.3 V to 2.7 V 2.7 V 3.0 V to 3.6 V 4.5 V to 5.5 V Test data Input VI VCC VCC 2.7 V 2.7 V VCC tr, tf Load CL RL 1 k 500 500 500 500 2.0 ns 30 pF 2.0 ns 30 pF 2.5 ns 50 pF 2.5 ns 50 pF 2.5 ns 50 pF VEXT tPLH, tPHL open open open open open tPZH, tPHZ GND GND GND GND GND tPZL, tPLZ 2 x VCC 2 x VCC 6.0 V 6.0 V 2 x VCC Supply voltage 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 13 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch 14. Additional dynamic characteristics Table 13: Additional dynamic characteristics At recommended conditions; typical values measured at Tamb = 25 C. Symbol dsin Parameter sine-wave distortion Conditions fi = 1 kHz; RL = 10 k; CL = 50 pF; see Figure 13 VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V fi = 10 kHz; RL = 10 k; CL = 50 pF; see Figure 13 VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V fON-state(res) switch ON-state signal frequency response RL = 600 ; CL = 50 pF; fi = 1 MHz; see Figure 14 VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V RL = 50 ; CL = 5 pF; fi = 1 MHz; see Figure 14 VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V OFF(ft) switch OFF-state signal feed-through attenuation RL = 600 ; CL = 50 pF; fi = 1 MHz; see Figure 15 VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V RL = 50 ; CL = 5 pF; fi = 1 MHz; see Figure 15 VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V [2] [2] [1] [1] Min Typ Max Unit - 0.032 0.008 0.006 0.001 - % % % % - 0.068 0.009 0.008 0.006 - % % % % - 135 145 150 155 - MHz MHz MHz MHz - >500 >500 >500 >500 - MHz MHz MHz MHz - -46 -46 -46 -46 - dB dB dB dB - -37 -37 -37 -37 - dB dB dB dB 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 14 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch Table 13: Additional dynamic characteristics ...continued At recommended conditions; typical values measured at Tamb = 25 C. Symbol Vct Parameter Conditions Min Typ Max Unit crosstalk between RL = 600 ; CL = 50 pF; fi = 1 MHz; control input to signal tr = tf = 2 ns; see Figure 16 output VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V fmax frequency response (-3 dB) RL = 50 ; CL = 10 pF; see Figure 14 VCC = 1.65 V VCC = 2.3 V VCC = 3.0 V VCC = 4.5 V Q injection charge CL = 0.1 nF; Vgen = 0 V; Rgen = 0 ; f = 1 MHz; RL = 1 M; VCC = 1.65 V to 5.5 V; see Figure 17 [3] [1] - 69 87 156 302 200 350 410 440 0.05 - mV mV mV mV MHz MHz MHz MHz pC [1] [2] [3] Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads -3 dB. Adjust fi voltage to obtain 0 dBm level at input. Definition: Q = Vout x CL. Guaranteed by design. 0.5 VCC VCC RL VIL E Z or Y 10 F Y or Z fi 600 CL D GND 001aaa366 Test conditions: VCC = 1.65 V: Vi = 1.4 V (p-p). VCC = 2.3 V: Vi = 2 V (p-p). VCC = 3 V: Vi = 2.5 V (p-p). VCC = 4 V: Vi = 4 V (p-p). Fig 13. Test circuit for measuring sine-wave distortion. 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 15 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch 0.5 VCC VCC RL VIL 0.1 F E Z or Y Y or Z fi 50 CL dB GND 001aaa364 Fig 14. Test circuit for measuring the frequency response when switch is in ON-state. 0.5 VCC VCC RL 0.5 VCC RL VIH 0.1 F E Z or Y Y or Z fi 50 CL dB GND 001aaa367 Fig 15. Test circuit for measuring feed-through attenuation when switch is in OFF-state. 0.5 VCC Ri = 600 0.5 VCC VCC E RL = 600 Y or Z Z or Y logic input 50 CL = 50 pF VO GND 001aaa363 Fig 16. Test circuit for measuring crosstalk between control input and output. 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 16 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch VCC E Y or Z Rgen logic input Vgen GND 001aaa362 RL = 1 M CL = 0.1 nF Z or Y VO logic (E) off input on off VO VOUT 001aaa368 Fig 17. Test circuit for measuring injection charge. 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 17 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch 15. Package outline Plastic surface mounted package; 5 leads SOT353 D B E A X y HE vMA 5 4 Q A A1 1 e1 e 2 bp 3 wM B detail X Lp c 0 1 scale 2 mm DIMENSIONS (mm are the original dimensions) UNIT mm A 1.1 0.8 A1 max 0.1 bp 0.30 0.20 c 0.25 0.10 D 2.2 1.8 E (2) 1.35 1.15 e 1.3 e1 0.65 HE 2.2 2.0 Lp 0.45 0.15 Q 0.25 0.15 v 0.2 w 0.2 y 0.1 OUTLINE VERSION SOT353 REFERENCES IEC JEDEC EIAJ SC-88A EUROPEAN PROJECTION ISSUE DATE 97-02-28 Fig 18. Package outline SOT353. 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 18 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch Plastic surface mounted package; 5 leads SOT753 D B E A X y HE vMA 5 4 Q A A1 c 1 2 3 detail X Lp e bp wM B 0 1 scale 2 mm DIMENSIONS (mm are the original dimensions) UNIT mm A 1.1 0.9 A1 0.100 0.013 bp 0.40 0.25 c 0.26 0.10 D 3.1 2.7 E 1.7 1.3 e 0.95 HE 3.0 2.5 Lp 0.6 0.2 Q 0.33 0.23 v 0.2 w 0.2 y 0.1 OUTLINE VERSION SOT753 REFERENCES IEC JEDEC JEITA SC-74A EUROPEAN PROJECTION ISSUE DATE 02-04-16 Fig 19. Package outline SOT753. 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 19 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch 16. Revision history Table 14: Revision history Release date 20040226 Data sheet status Product data Change notice Order number 9397 750 12675 Supersedes Document ID 74LVC1G384_1 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 20 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch 17. Data sheet status Level I II Data sheet status [1] Objective data Preliminary data Product status [2] [3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). III Product data Production [1] [2] [3] Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 18. Definitions Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 19. Disclaimers Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 20. Contact information For additional information, please visit http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com 9397 750 12675 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved. Product data sheet Rev. 01 -- 26 February 2004 21 of 22 Philips Semiconductors 74LVC1G384 Bilateral switch 21. Contents 1 2 3 4 5 6 7 7.1 7.2 8 8.1 9 10 11 12 13 14 15 16 17 18 19 20 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 3 Function table . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 4 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Dynamic characteristics . . . . . . . . . . . . . . . . . 10 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Additional dynamic characteristics . . . . . . . . 14 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 20 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 21 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Contact information . . . . . . . . . . . . . . . . . . . . 21 (c) Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 26 February 2004 Document order number: 9397 750 12675 Published in The Netherlands |
Price & Availability of 74LVC1G384GW
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |